Do It RIGHT! How to Fix a Broken Window Pane

Jordan Smith
Jordan Smith
349,313
0
Published 2019-07-04
How do you replace the glazing in a single hung window? In this episode Jordan walks you through the process of replacing a broken window pane step by step.
Replacing a non-operable window pane can be slightly more complicated than in a window where the sash can be removed because you have to work on both sides of the wall, instead of simply removing the sash and working on a work bench.
However, it is steill a pretty simple straightforward task and can be accomplished in less than a hour if you have the right tools and know what to expect.
Here are the tools we used:
Cut Resistant Gloves - amzn.to/2xxE9ag
Prazi Utility Knife - amzn.to/2JrpK52
Olfa 9MM Utility Knife - amzn.to/2RQVyEq
Double Ended Window Tool - amzn.to/2xsRbpL
Caulk Gun - amzn.to/2JrqBTi
Silicon - amzn.to/2JrqBTi
Spray Bottle - amzn.to/2XmEVBD
Alcohol - amzn.to/2Xr2f10

Step 1: Tape off broken window to prevent shattering and a messy cleanup
Step 2: Mask window frame to prevent silicone from squeezing out onto it
Step 3: Cut exterior retention beads and remove
Step 4: Cut interior silicone bead
Step 5: Remove broken pane with double ended window tool.
Step 6: Remove old silicone bead from window frame (be sure to keep the spacers!)
Step 7: Dry fit the new window pane and mask the interior next to the window frame to prevent excess silicone from contacting the glass.
Step 8: Apply silicone to exterior of window frame
Step 9: Set window on saved spacers
Step 10: Apply new exterior retention beads
Step 11: Clean Up!
All Comments (21)
  • @boomdoggy
    Very well presented and articulated.
  • @justicefall1917
    I’ve always wondered how you replace the glass in a vinyl frame window. Thank you Jordan for taking the time to show us how it’s done and to save us from calling a glass repair shop! Another great video!!
  • @lexiemn
    Nice job. You explain the process very well.
  • @truckerjack531
    Good Job! If you want the silicone not to make a mess, I cut the tip of the caulking tube smaller to start remember if you use a smaller cut to start with you can cut the tip bigger Until your ok with the amount of caulking coming out of the tube. And if you cut the tip to big and you make a mess, then you have to get a new tube and start over.
  • @anthonymehring2064
    I do this for a living. Cutting the bead is unnecessary and will actually take more time because you have to pull out the piece that is still in the slot after you cut it. Also, if you had simply used your green utility knife and made several careful and deep passes when cutting out the old silicone/double faced tape, there would be no need for the tape to hold the window together. Also using a ton of silicone is unnecessary, making the masking tape unnecessary. And if there is any that seeps through, just wait for it to dry and then cut it away with your knife, or clean it with a utility blade and glass cleaner as lubricant. Just be careful not to scratch the glass. Finally, if you are by yourself, cut the old silicone/double faced tape thoroughly before removing the bead from the out side. It’s a lot safer. Then when you remove the bead, just pull the double pane out with a L shaped bar prying into the rubber of the double pane, not the glass, and catch it. Also make sure that the black rubber blocks on the bottom are not stuck to the bottom of the old double pane, so you can set the new one on them for protection. Those are my suggestions. I literally did these steps on several windows at work, just today. I’ve done this thousands of times. Just some tips for you.
  • @Mugotti
    Great video thanks 💯💪🏾
  • @trshuster
    That job is no fun for sure. As an Andersen dealer we have to do it from time to time. Well done sir and best wishes on your new venture. I'll be subscribing.